Company ID

GREASE DISPENSERS

G.P. Reeves manufactures a huge array of grease dispensers. All are "positive displacement" dispensers, ejecting a measured shot of grease each cycle, unaffected by time, temperature, or grease viscosity. See the wide variety of styles and sizes.

GSS Air Operated Grease Dispensers

  • Accurate, Reliable, Repeatable
  • For low pressure grease - 200 psi maximum
  • For NLGI 000 through NLGI 3 grease
  • Uses adjustable volumetric piston displacement to dispense measured shots of grease 
  • Dispenses set amounts of grease regardless of temperature and viscosity changes.  See chart for part numbers and sizes
  • Fast – up to 180 operations per minute

Typical Uses Include:

  • Dashboard and console pivots and buttons
  • Locking and latching components
  • Electrical terminals
  • Automotive HVAC components

GSS-001PNP
GSS-001PNP
GSS dispenser, adjustable, with maximum output of 0.001 cubic inch (0.016 cc) includes "O" ring and tapped surface on outlet end.  An integral 10-30 VDC PNP piston stroke sensor outputs when air piston is in the "dispensed" positions.   Sensor includes LED and its connector is M8.  Lube input port is 1/4 NPT and maximum recommended grease inlet pressure is 200 p.s.i.  Air port is 10-32 and dispenser operates with a 3-way air valve with minimum of 60 p.s.i.  Adaptors and sandwich blocks can be purchased for installation on outlet end. 
GSS-001PNP 3D Model SolidWorks Logo


GSS-002PNP
GSS-002PNP
GSS dispenser, adjustable, with maximum output of 0.002 cubic inch (0.033 cc) includes "O" ring and tapped surface on outlet end.  An integral 10-30 VDC PNP piston stroke sensor outputs when air piston is in the "dispensed" positions.   Sensor includes LED and its connector is M8.   Lube input port is 1/4 NPT and maximum recommended grease inlet pressure is 200 p.s.i.  Air port is 10-32 and dispenser operates with a 3-way air valve with minimum of 60 p.s.i.  Adaptors and sandwich blocks can be purchased for installation on outlet end. 
GSS-002PNP 3D Model SolidWorks Logo


GSS-004PNP
GSS-004PNP
GSS dispenser, adjustable, with maximum output of 0.004 cubic inch (0.066 cc) includes "O" ring and tapped surface on outlet end. An integral 10-30 VDC PNP piston stroke sensor outputs when air piston is in the "dispensed" positions.  Sensor includes LED and its connector is M8.   Lube input port is 1/4 NPT and maximum recommended grease inlet pressure is 200 p.s.i.  Air port is 10-32 and dispenser operates with a 3-way air valve with minimum of 60 p.s.i.  Adaptors and sandwich blocks can be purchased for installation on outlet end.
GSS-004PNP 3D Model SolidWorks Logo


GSS-001NPN
GSS-001NPN
GSS dispenser, adjustable, with maximum output of 0.001 cubic inch (0.016 cc) includes "O" ring and tapped surface on outlet end.  An integral 10-30 VDC NPN piston stroke sensor outputs when air piston is in the "dispensed" positions.   Sensor includes LED and its connector is M8.  Lube input port is 1/4 NPT and maximum recommended grease inlet pressure is 200 p.s.i.  Air port is 10-32 and dispenser operates with a 3-way air valve with minimum of 60 p.s.i.  Adaptors and sandwich blocks can be purchased for installation on outlet end. 
GSS-001NPN 3D Model SolidWorks Logo


GSS-002NPN
GSS-002NPN
GSS dispenser, adjustable, with maximum output of 0.002 cubic inch (0.033 cc) includes "O" ring and tapped surface on outlet end.  An integral 10-30 VDC NPN piston stroke sensor outputs when air piston is in the "dispensed" positions.  Sensor includes LED and its connector is M8.  Lube input port is 1/4 NPT and maximum recommended grease inlet pressure is 200 p.s.i.  Air port is 10-32 and dispenser operates with a 3-way air valve with minimum of 60 p.s.i. Adaptors and sandwich blocks can be purchased for installation on outlet end. 
GSS-002NPN 3D Model SolidWorks Logo


GSS-004NPN
GSS-004NPN
GSS dispenser, adjustable, with maximum output of 0.004 cubic inch (0.066 cc) includes "O" ring and tapped surface on outlet end.  An integral 10-30 VDC NPN piston stroke sensor outputs when air piston is in the "dispensed" positions.   Sensor includes LED and its connector is M8.   Lube input port is 1/4 NPT and maximum recommended grease inlet pressure is 200 p.s.i.  Air port is 10-32 and dispenser operates with a 3-way air valve with minimum of 60 p.s.i.  Adaptors and sandwich blocks can be purchased for installation on outlet end. 
GSS-004NPN 3D Model SolidWorks Logo


GSS-011
GSS-011
GSS dispenser, adjustable, with maximum output of 0.001 cubic inch (0.016 cc) includes "O" ring and tapped surface on outlet end.  Lube input port is 1/4 NPT and maximum recommended grease inlet pressure is 200 p.s.i..  Air port is 10-32 and dispenser operates with a 3-way air valve.  Adaptors and sandwich blocks can be purchased for installation on outlet end. 
GSS-011 3D Model SolidWorks Logo


GSS-012
GSS-012
GSS dispenser, adjustable, with maximum output of 0.002 cubic inch (0.033 cc) includes "O" ring and tapped surface on outlet end.  Lube input port is 1/4 NPT and maximum recommended grease inlet pressure is 200 p.s.i.  Air port is 10-32 and dispenser operates with a 3-way air valve with minimum of 60 p.s.i.  Adaptors and sandwich blocks can be purchased for installation on outlet end.  .
GSS-012 3D Model SolidWorks Logo


GSS-014
GSS-014
GSS dispenser, adjustable, with maximum output of 0.004 cubic inch (0.066 cc) includes "O" ring and tapped surface on outlet end.  Lube input port is 1/4 NPT and maximum recommended grease inlet pressures is 200 p.s.i.  Air port is 10-32 and dispenser operates with a 3-way air valve with minimum of 60 p.s.i.  Adaptors and sandwich blocks can be purchased for installation on outlet end. 
GSS-014 3D Model SolidWorks Logo


OUTLET ADAPTORS & FITTINGS

Part number

Description

GSS-003

Bijur port for 5/32 OD (4 mm) tube

GSS-005

10-32 port

GSS-006

1/4-28 port

GSS-007

Leur lock fitting with 1/4-28 male

GSS-008

1/8 NPT port

GSS-010

Dual inlet – single 1/8 NPT outlet

GSS-016

for installation on tapped tooling

GSS-031

M5 x .8 port

GSS-032

5/16-32 port for Chinese needle

GSS-037

SAE-2 (female) port

 

GSS Grease Dispensers Brochure Adobe Logo
How GSS dispensers work brochure Adobe Logo

GSSM Air Operated Grease Dispensers

  • Accurate, Reliable, Repeatable
  • For Low pressure grease - 200 psi maximum
  • For NGLI 000 through NLGI 3 grease
  • Uses adjustable volumetric piston displacement to dispense measured shots of grease
  • Dispenses set amounts of grease regardless of temperature and viscosity changes. See chart for part numbers and sizes
  • Fast – up to 180 operations per minute

Typical Uses Include:

  • Dashboard and console pivots and buttons
  • Locking and latching components
  • Electrical terminals
  • Automotive HVAC components

GSSM-001PNP
GSSM-001PNP
GSSM (manifold mountable) dispenser, adjustable, with maximum output of 0.001 cubic inch (0.016 cc) includes "O" ring and tapped surface on outlet end.  An integral 10-30 VDC PNP piston stroke sensor outputs when air piston is in the "dispensed" positions.   Sensor includes LED and its connector is M8.  Grease and air input ports are on bottom.  Maximum recommended grease inlet pressure is 200 p.s.i.   Dispenser operates with a 3-way air valve with minimum of 60 p.s.i.  GSS series adaptors and sandwich blocks can be purchased for installation on outlet end.  Mounting bolts and seals are included for installation on GSSMB.
GSSM-001PNP 3D Model SolidWorks Logo


GSSM-002PNP
GSSM-002PNP
GSSM (manifold mountable) dispenser, adjustable, with maximum output of 0.002 cubic inch (0.033 cc)  includes "O" ring and tapped surface on outlet end.  An integral 10-30 VDC PNP piston stroke sensor outputs when air piston is in the "dispensed" positions.   Sensor includes LED and its connector is M8.  Grease and air input ports are on bottom.  Maximum recommended grease inlet pressure is 200 p.s.i.   Dispenser operates with a 3-way air valve with minimum of 60 p.s.i.  GSS series adaptors and sandwich blocks can be purchased for installation on outlet end.  Mounting bolts and seals are included for installation on GSSMB.
GSSM-002PNP 3D Model SolidWorks Logo


GSSM-004PNP
GSSM-004PNP
GSSM (manifold mountable) dispenser, adjustable, with maximum output of 0.004 cubic inch (0.066 cc)  includes "O" ring and tapped surface on outlet end.  An integral 10-30 VDC PNP piston stroke sensor outputs when air piston is in the "dispensed" positions.   Sensor includes LED and its connector is M8.  Grease and air input ports are on bottom.  Maximum recommended grease inlet pressure is 200 p.s.i.   Dispenser operates with a 3-way air valve with minimum of 60 p.s.i.  GSS series adaptors and sandwich blocks can be purchased for installation on outlet end.  Mounting bolts and seals are included for installation on GSSMB.
GSSM-004PNP 3D Model SolidWorks Logo


GSSM-001NPN
GSSM-001NPN
GSSM (manifold mountable) dispenser, adjustable, with maximum output of 0.001 cubic inch (0.016 cc) includes "O" ring and tapped surface on outlet end.  An integral 10-30 VDC NPN piston stroke sensor outputs when air piston is in the "dispensed" positions.   Sensor includes LED and its connector is M8.  Grease and air input ports are on bottom.  Maximum recommended grease inlet pressure is 200 p.s.i.   Dispenser operates with a 3-way air valve with minimum of 60 p.s.i.  GSS series adaptors and sandwich blocks can be purchased for installation on outlet end.  Mounting bolts and seals are included for installation on GSSMB.
GSSM-001NPN 3D Model SolidWorks Logo


GSSM-002NPN
GSSM-002NPN
GSSM (manifold mountable) dispenser, adjustable, with maximum output of 0.002 cubic inch (0.033 cc)  includes "O" ring and tapped surface on outlet end.  An integral 10-30 VDC NPN piston stroke sensor outputs when air piston is in the "dispensed" positions.   Sensor includes LED and its connector is M8.  Grease and air input ports are on bottom.  Maximum recommended grease inlet pressure is 200 p.s.i.   Dispenser operates with a 3-way air valve with minimum of 60 p.s.i.  GSS series adaptors and sandwich blocks can be purchased for installation on outlet end.  Mounting bolts and seals are included for installation on GSSMB.
GSSM-002NPN 3D Model SolidWorks Logo


GSSM-004NPN
GSSM-004NPN
GSSM (manifold mountable) dispenser, adjustable, with maximum output of 0.004 cubic inch (0.066 cc)  includes "O" ring and tapped surface on outlet end.  An integral 10-30 VDC NPN piston stroke sensor outputs when air piston is in the "dispensed" positions.   Sensor includes LED and its connector is M8.  Grease and air input ports are on bottom.  Maximum recommended grease inlet pressure is 200 p.s.i.   Dispenser operates with a 3-way air valve with minimum of 60 p.s.i.  GSS series adaptors and sandwich blocks can be purchased for installation on outlet end.  Mounting bolts and seals are included for installation on GSSMB.
GSSM-004NPN 3D Model SolidWorks Logo


GSSM-011
GSSM-011
GSSM (manifold mountable) dispenser, adjustable, with maximum output of 0.001 cubic inch (0.016 cc) includes "O" ring and tapped surface on outlet end.  Grease and air input ports are on bottom.   Maximum recommended grease inlet pressure is 200 p.s.i.   Dispenser operates with a 3-way air valve with minimum of 60 p.s.i.  GSS series adaptors and sandwich blocks can be purchased for installation on outlet end.  Mounting bolts and manifold seals are included.  Mounting bolts and seals are included for installation on any GSSMB.
GSSM-011 3D Model SolidWorks Logo


GSSM-012
GSSM-012
GSSM (manifold mountable) dispenser, adjustable, with maximum output of 0.002 cubic inch (0.033 cc) includes "O" ring and tapped surface on outlet end.  Grease and air input ports are on bottom.    Maximum recommended grease inlet pressure is 200 p.s.i.  Dispenser operates with a 3-way air valve with minimum of 60 p.s.i.  GSS series adaptors and sandwich blocks can be purchased for installation on outlet end.  Mounting bolts and seals are included for installation on any GSSMB.
GSSM-012 3D Model SolidWorks Logo


GSSM-014
GSSM-014
GSSM (manifold mountable) dispenser, adjustable, with maximum output of 0.004 cubic inch (0.066 cc) includes "O" ring and tapped surface on outlet end.  Grease and air input ports are on bottom.   Maximum recommended grease inlet pressure is 200 p.s.i.  Dispenser operates with a 3-way air valve with minimum of 60 p.s.i.  GSS series adaptors and sandwich blocks can be purchased for installation on outlet end.  Mounting bolts and seals are included for installation on any GSSMB.
GSSM-014 3D Model SolidWorks Logo


GSSM-003
GSSM-003
Block plate for installation on any GSSM manifold. Takes the place of GSSM dispenser to allow unused manifold station.
GSSM-003 3D Model SolidWorks Logo


GSSMB MANIFOLD PART BUILDER

Basic Part Number

Number of Stations

Separate Air Ports

GSSMB

-10

SA

Examples:  (maximum number of stations is ten)

Part number GSSMB-10SA is a ten-station manifold with separate 1/8 NPT air ports

Part number GSSMB-10 is a ten-station manifold without separate air ports

Part number GSSMB-2 is a two-station manifold without separate air ports

 

 

OUTLET ADAPTORS & FITTINGS

Part number

Description

GSS-003

Bijur port for 5/32 OD (4 mm) tube

GSS-005

10-32 port

GSS-006

1/4-28 port

GSS-007

Leur lock fitting with 1/4-28 male

GSS-008

1/8 NPT port

GSS-010

Dual inlet – single 1/8 NPT outlet

GSS-016

for installation on tapped tooling

GSS-031

M5 x .8 port

GSS-032

5/16-32 port for Chinese needle

GSS-037

SAE-2 port

 

GSSM Grease Dispensers Brochure Adobe Logo
How The GSSM Dispensers Work brochure Adobe Logo
GSSMB-1 3D Model SolidWorks Logo
GSSMB-2 3D Model SolidWorks Logo
GSSMB-2SA 3D Model SolidWorks Logo
GSSMB-3 3D Model SolidWorks Logo
GSSMB-3SA 3D Model SolidWorks Logo
GSSMB-4 3D Model SolidWorks Logo
GSSMB-4SA 3D Model SolidWorks Logo
GSSMB-5 3D Model SolidWorks Logo
GSSMB-5SA 3D Model SolidWorks Logo
GSSMB-6 3D Model SolidWorks Logo
GSSMB-6SA 3D Model SolidWorks Logo
GSSMB-8 3D Model SolidWorks Logo
GSSMB-9 3D Model SolidWorks Logo

GPMD10000 Series Grease Dispensers

Base-mountable, air-operated, single-acting, adjustable, metered shot (piston) dispensers.

  • Accurate dispensing of 0.02 cc to 3.69 cc shots of grease (depending on model selected).
  • Positive piston displacement dispenser accurately delivers measured shots of grease.
  • Change shot size quickly and easily using finethread adjustment screw with lock nut.
  • Bases are available with from 1 to 8 stations and also with separate air inlets for independent operation.
  • Can dispense up to 40 times per minute at maximum shot size.
  • Uses piston displacement to measure grease and will dispense set amounts regardless of temperature.
  • Operates at 50 to 120 psi with 3-way NC Air Valve.
  • Operates with low pressure grease (up to 200 psi).

Note: Basic part number must include at least one Option ID to be complete. The part number for a dispenser with no options will include the suffix -00. Separate additional options with dashes.

See complete part number examples below: (enter option numbers in order – lowest number to highest number)

GPMD10020-00 is a 10000 series dispenser with an adjustable volume of 0.02 to 0.20 cc, a boost ratio of 36 to 1, and no other
installed options.

GPMD10125-01-03 is a 10000 series dispenser with an adjustable volume of 0.06 to 1.25 cc, a boost ratio of 11.56 to 1, one stroke
sensor, and a calibration scale.

GPMD10020-__-__-__
GPMD10020-__-__-__

Positive displacement grease dispenser, base mountable, air-operated, single-acting, 1/8 NPT outlet port, adjustable from 0.02 to 0.20 cc, with 36 to 1 boost ratio.

__-__-__ See OPTION LIST below to complete part number. Include at least one option. There is no maximum number of options.

Example: GPMD10020-00, GPMD10020-01-03, GPMD10020-01-03-07


GPMD10020-00 3D Model SolidWorks Logo


GPMD10080-__-__-__
GPMD10080-__-__-__

Positive displacement grease dispenser, base mountable, air-operated, single-acting, 1/8 NPT outlet port, adjustable from 0.02 to 0.80 cc, with 12.25 to 1 boost ratio.

__-__-__ See OPTION LIST below to complete part number. Include at least one option. There is no maximum number of options.

Example: GPMD10080-00, GPMD10080-01-03, GPMD10080-01-03-07


GPMD10080-00 3D Model SolidWorks Logo


GPMD10125-__-__-__
GPMD10125-__-__-__

Positive displacement grease dispenser, base mountable, air-operated, single-acting, 1/8 NPT outlet port, adjustable from 0.06 to 1.25 cc, with 11.56 to 1 boost ratio.

__-__-__ See OPTION LIST below to complete part number. Include at least one option. There is no maximum number of options.

Example: GPMD10125-00, GPMD10125-01-03, GPMD10125-01-03-07


GPMD10125-00 3D Model SolidWorks Logo


GPMD10369-__-__-__
GPMD10369-__-__-__

Positive displacement grease dispenser, base mountable, air-operated, single-acting, 1/8 NPT outlet port,  adjustable from 0.13 to 3.69 cc, with 11.76 to 1 boost ratio.

__-__-__ See OPTION LIST below to complete part number. Include at least one option. There is no maximum number of options.

Example: GPMD10369-00, GPMD10369-01-03, GPMD10369-01-03-07


GPMD10369-00 3D Model SolidWorks Logo


OPTION LIST

(choose one or more)

NOTES:

Each M8 stroke sensor requires a #0893 cord

Single stroke sensors will be factory set to recognize “dispense complete”

Each flow sensor or M12 stroke sensor requires a #1850 cord

Stroke sensors with clamps (04, 05, & 08) can not be used with calibration scale (03)

Option ID

Option Description

Notes:

00

No options (dispenser will have a magnetic piston)

Does not have sensor track

01

Single M8 PNP stroke sensor (has short cord and M8 DC connector)

Factory install only (W/ track)

02

Two M8 PNP stroke sensors (has two short cords and two M8 DC connectors)

Factory install only (W/track)

03

Calibration scale (not for use with stroke sensors with clamps)

Can be added later

04

Single M8 PNP stroke sensor on clamp (has short cord and M8 DC connector)

Factory installation or add later

05

Single M8 NPN stroke sensor on clamp (has short cord and M8 DC connector)

Factory installation or add later

06

Flow sensor (integral) has 2 PNP outputs and an M12 connector.  For 1,000 psi max. at flow applications.  Recommended for use with NLGI #0 to NLGI #2 grease. 

Factory installation only

07

Manual bleed valve installed in place of 1/8 NPT bleed plug

Factory installation or add later

08

Single M12 PNP stroke sensor on clamp (not available with calibration scale)

Factory installation or add later

09

Flow sensor (integral) has 2 PNP outputs and an M12 connector.  For 3,000 psi max. at flow applications.  Recommended for use with NLGI #2 to NLGI #4 grease. 

Factory installation only

12

Two M8 NPN stroke sensors (has two short cords and two M8 DC connectors)

Factory install only (W/track)

15

Single M8 NPN stroke sensor (has short cord and M8 DC connector)

Factory install only (W/track)

 

All MDM1000 manifolds have 1/4 NPT grease inlet ports on both ends

GPMD10000 Series Dispensers can not be used without manifolds

Note: All GPMD 10000 series dispensers are designed for installation on MDM1000 series manifolds and for use with a maximum of 200 psi grease inlet pressure

 

 

Bases with 1/4 NPT common air ports on both ends are for simultaneous operation of all grease dispensers

 

Bases with 1/8 NPT separate air ports on side are for independent operation of each grease dispenser

Part Number

Description

 

Part Number

Description

MDM1000-1

Single station manifold

 

separate air is not necessary with a single station manifold

MDM1000-2

Two station manifold

 

MDM1000-2SA

Two station manifold – separate air

MDM1000-3

Three station manifold

 

MDM1000-3SA

Three station manifold – separate air

MDM1000-4

Four station manifold

 

MDM1000-4SA

Four station manifold – separate air

MDM1000-5

Five station manifold

 

MDM1000-5SA

Five station manifold – separate air

MDM1000-6

Six station manifold

 

MDM1000-6SA

Six station manifold – separate air

MDM1000-7

Seven station manifold

 

MDM1000-7SA

Seven station manifold – separate air

MDM1000-8

Eight station manifold

 

MDM1000-8SA

Eight station manifold – separate air

 

MDM1000-1 3D Model SolidWorks Logo
MDM1000-2 3D Model SolidWorks Logo
MDM1000-3 3D Model SolidWorks Logo
MDM1000-4 3D Model SolidWorks Logo
MDM1000-5 3D Model SolidWorks Logo
MDM1000-6 3D Model SolidWorks Logo
GPMD10000 Series Brochure Adobe Logo

GPMD15000 Series Grease Dispensers

Nose-mountable, air-operated, single-acting, adjustable, metered shot (piston) dispensers.

  • Accurate dispensing of 0.02 cc to 6.20 cc shots of grease (depending on model selected).
  • Positive piston displacement dispenser accurately delivers measured shots of grease.
  • Change shot size quickly and easily using fine-thread adjustment screw with lock nut.
  • Swivel grease outlet allow inlet port to point in any direction and also facilitates easy installation
  • Can dispense up to 40 times per minute at maximum shot size.
  • Uses piston displacement to measure grease and will dispense set amounts regardless of temperature.
  • Operates at 50 to 120 psi with 3-way NC Air Valve.
  • Operates with low pressure grease (up to 200 psi).

Notes: Basic part number must include at least one Option ID to be complete. The part number for a dispenser with no options should include the suffix -00. The GPMD15620-00 can not be adjusted to dispense less than 2 cc.

See complete part number examples below: (enter suffix numbers in ascending order – lowest number to highest number)

GPMD15020-00 is a 15000 series dispenser with an adjustable volume of 0.02 to 0.20 cc, a boost ratio of 36 to 1, and no other installed options.

GPMD15125-01-03-07 is a 15000 series dispenser with an adjustable volume of 0.06 to 1.25 cc, a boost ratio of 11.56 to 1, one stroke sensor, a calibration scale, and a manual bleed valve.

GPMD15020-__-__-__
GPMD15020-__-__-__

GPMD air operated grease dispenser is positive displacement, 1/4 NPT male nose swivel mountable, adjustable from 0.02 to 0.20 cc, has a 36 : 1 boost ratio, and can function with 200 psi grease supply pressure.

__-__-__ See OPTION LIST below to complete part number. Include at least one option. There is no maximum number of options.

Example: GPMD15020-00, GPMD15020-01-03, GPMD15020-01-03-07


GPMD15020-00 3D Model SolidWorks Logo


GPMD15080-__-__-__
GPMD15080-__-__-__

GPMD air operated grease dispenser is positive displacement, 1/4 NPT male nose swivel mountable, adjustable from 0.02 to 0.80 cc, has a 12.5 : 1 boost ratio, and can function with 200 psi grease supply pressure.

__-__-__ See OPTION LIST below to complete part number. Include at least one option. There is no maximum number of options.

Example: GPMD15080-00, GPMD15080-01-03, GPMD15080-01-03-07


GPMD15080-00 3D Model SolidWorks Logo


GPMD15125-__-__-__
GPMD15125-__-__-__

GPMD air operated grease dispenser is positive displacement, 1/4 NPT male nose swivel mountable, adjustable from 0.06 to 1.25 cc, has a 11.56 : 1 boost ratio, and can function with 200 psi grease supply pressure.

__-__-__ See OPTION LIST below to complete part number. Include at least one option. There is no maximum number of options.

Example: GPMD15125-00, GPMD15125-01-03, GPMD15125-01-03-07


GPMD15125-00 3D Model SolidWorks Logo


GPMD15369-__-__-__
GPMD15369-__-__-__

GPMD air operated grease dispenser is positive displacement,1/4 NPT male nose swivel mountable, adjustable from 0.13 to 3.69 cc, has a 11.76 : 1 boost ratio, and can function with 200 psi grease supply pressure.

__-__-__ See OPTION LIST below to complete part number. Include at least one option. There is no maximum number of options.

Example: GPMD15369-00, GPMD15369-01-03, GPMD15369-01-03-07


GPMD15369-00 3D Model SolidWorks Logo


GPMD15620-__-__-__
GPMD15620-__-__-__

GPMD air operated grease dispenser is positive displacement,1/4 NPT male nose swivel mountable, adjustable from 2.00 to 6.20 cc, has a 10.24 : 1 boost ratio, and can function with 200 psi grease supply pressure.

__-__-__ See OPTION LIST below to complete part number. Include at least one option. There is no maximum number of options.

Example: GPMD15620-00, GPMD15620-01-03, GPMD15620-01-03-07


GPMD15620-00 3D Model SolidWorks Logo


OPTION LIST

(choose one or more)

NOTES:

Each M8 stroke sensor requires a #0893 cord

Single stroke sensors will be factory set to recognize “dispense complete”

Each flow sensor or M12 stroke sensor requires a #1850 cord

Stroke sensors with clamps (01, 05, & 08) can not be used with calibration scale (03)

Option ID

Option Description

Notes:

00

No options (dispenser will have a magnetic piston)

Does not have sensor track

01

Single M8 PNP stroke sensor (has short cord and M8 DC connector)

Factory install only (W/ track)

02

Two M8 PNP stroke sensors (has two short cords and two M8 DC connectors)

Factory install only (W/track)

03

Calibration scale (not for use with stroke sensors with clamps)

Factory installation or add later

04

Single M8 PNP stroke sensor on clamp (has short cord and M8 DC connector)

Factory installation or add later

05

Single M8 NPN stroke sensor on clamp (has short cord and M8 DC connector)

Factory installation or add later

06

Flow sensor (installed) has 2 PNP outputs and an M12 connector.  For 1,000 psi. max. applications.  Recommended for use with NLGI #0 to NLGI #2 grease.

Factory installation or add later

07

Manual bleed valve installed in place of 1/8 NPT bleed plug

Factory installation or add later

08

Single M12 PNP stroke sensor on clamp (not available with calibration scale)

Factory installation or add later

09

Flow sensor (installed) has 2 PNP outputs and an M12 connector.  For 3,000 psi max. at flow applications.  Recommended for use with NLGI #2 to NLGI #4 grease.

Factory installation or add later

11

KA6003 mounting block installed on dispenser changes the grease outlet port to 1/4 NPT female and also provides vertical and horizontal mounting holes and a SAE-4 port for installation of a (not included) EPS1001 electronic pressure sensor. 

Factory installation or add later

12

Two M8 NPN stroke sensors (has two short cords and two M8 DC connectors)

Factory install only (W/track)

13

Block type spray nozzle asm. includes machined manifold with two mounting holes, 1/4 NPT grease inlet port, 4393 meter in needle valve installed in its 1/8 NPT air inlet port.  Replaceable tip is our number KA4437.  Spray pattern is solid cone and, with NLGI #2 grease, at 1" distance, the pattern will have about 1/2" diameter.  

Factory installation or add later

14

Block type spray nozzle asm. (same as option 13), except also includes an integral 1,000 psi flow sensor with 2 PNP outputs and an M12 connector.

Factory installation or add later

15

Single M8 NPN stroke sensor (has short cord and M8 DC connector)

Factory install only (W/track)

16

Hand-held vertical dispense handle with bracket for tool balancer, electronic trigger, 24 VDC solenoid valve, and an assortment of stainless steel nozzles.

Factory installation or add later

GPMD15000 Series Brochure Adobe Logo

GPMD2000 Series Grease Dispensers

Reliable, PLC compatible, air-operated, single-acting, volumetric piston dispenser

GPMD2000 series dispensers are positive displacement and include two air pilot operated check valves, two piston position proximity sensors, a stroke adjustment mechanism, a cc scale, and require 10-30 VDC and two or three 3-way air valves and a minimum of 55 psi compressed air for operation.

  • Accurate repetitive dispensing regardless of temperature and viscosity changes
  • Dispense up to 10 shots per minute at maximum shot size
  • Function with almost any oil or grease to 1,000,000 centipoise
  • Air operated check valves prevent leaking
  • Visual indication of adjustment and function
  • Operate with grease inlet pressure between 400 and 3,000 psi

 

GPMD2008-ACE1
GPMD2008-ACE1

Air operated positive displacement grease dispenser adjustable between .50 and 7.31cc and complete with 24 VDC PNP proximity sensors and adjustment scale. One sensor indicates FILLED and the other sensor indicates DISPENSED. Complete with 1/4 NPT inlet and outlet ports, 1/8 NPT bleed port, and air pilot operated cartridge valves for inlet and outlet. This dispenser requires two 3 way air valves and grease pressure between 400-3,000 PSI for operation. Air valves can operate at 60 to 100 p.s.i. Boost ratio is 11 to 1. Requires 1850 Cord.


GPMD2008-ACE1 CAT Sheet Adobe Logo
GPMD2008-ACE1 3D Model SolidWorks Logo


GPMD2009-ACE1
GPMD2009-ACE1

Air operated positive displacement grease dispenser adjustable between 1.00 and 16.00cc and complete with 24 VDC PNP proximity sensors and adjustment scale. One sensor indicates FILLED and the other sensor indicates DISPENSED. Complete with 1/4 NPT inlet and outlet ports, 1/8 NPT bleed port, and air pilot operated cartridge valves for inlet and outlet. This dispenser requires two 3 way air valves and grease pressure between 400-2,000 PSI for operation. Air valves can operate at 60 to 100 p.s.i. Boost ratio is 9 to 1. Requires 1850 Cord.


GPMD2009-ACE1 CAT Sheet Adobe Logo
GPMD2009-ACE1 3D Model SolidWorks Logo


GPMD2011-ACE1
GPMD2011-ACE1

Air operated positive displacement grease dispenser adjustable between .12 and 1.50 cc and complete with 24 VDC PNP proximity sensors and adjustment scale. One sensor indicates FILLED and the other sensor indicates DISPENSED. Dispenser has 1/4 NPT inlet and outlet ports, 1/8 NPT bleed port, and air pilot operated cartridge valves for inlet and outlet. This dispenser requires two or three 3 way NC solenoid valves and grease pressure between 500-3,000 PSI for operation. Air valves can operate at 60 to 100 p.s.i. Boost ratio is 32 to 1. Requires 1850 Cord.


GPMD2011-ACE1 CAT Sheet Adobe Logo
GPMD2011-ACE1 3D Model SolidWorks Logo


GPMD2012-ACE1
GPMD2012-ACE1

Air operated positive displacement grease dispenser adjustable between .05 and .40 cc and complete with 24 VDC PNP proximity sensors and adjustment scale. One sensor indicates FILLED and the other sensor indicates DISPENSED. Dispenser has 1/4 NPT inlet and outlet ports, 1/8 NPT bleed port, and air pilot operated cartridge valves for inlet and outlet. This dispenser requires two or three 3 way NC solenoid valves and grease pressure between 200-3,000 PSI for operation. Air valves can operate at 60 to 100 p.s.i. Boost ratio is 12 to 1. Requires 1850 Cord.


GPMD2012-ACE1 CAT Sheet Adobe Logo
GPMD2012-ACE1 3D Model SolidWorks Logo


GPMD2014-ACE1
GPMD2014-ACE1

Air operated positive displacement grease dispenser adjustable between 0.02 and 0.40 cc and complete with 24 VDC PNP proximity sensors and adjustment scale.  One sensor indicates FILLED and the other sensor indicates DISPENSED.  Dispenser has 1/4 NPT inlet and outlet ports, 1/8 NPT bleed port, and air pilot operated cartridge valves for inlet and outlet.  This dispenser requires two or three 3 way NC solenoid valves and grease pressure between 400-3,000 PSI for operation.  Air valves can operate at 60 to 100 p.s.i.  Boost ratio is 12 to 1. 


GPMD2014-ACE1 CAT Sheet Adobe Logo
GPMD2014-ACE1 3D Model SolidWorks Logo


OPTIONS

Part Number

Description

1850

Cord with 4-pin Micro connector

3850

Bleed valve with 1/8 NPT ports

EPS1001

Electronic Pressure Sensor – 0-60 bar (870 p.s.i.), SAE 04 male pressure fitting, 0 to 10 Volt output, 4-pin Micro connector.  Includes a sample program for use with A-B Micrologix PLC.  This sensor requires an analog input to the user’s PLC.

 

GPMD 2000 Series Catalog Page Adobe Logo

GPMD3000 Series Grease Dispensers

Reliable, PLC compatible, air-operated, single-acting, volumetric piston dispenser.

GPMD3000 series dispensers are positive displacement and include two air pilot operated check valves and a threaded rod stroke adjustment mechanism with a jam nut. They require two or three 3-way air valves and a minimum of 55 psi compressed air for operation. Additional stroke sensors are optional.

  • Accurate repetitive dispensing regardless of temperature and viscosity changes
  • Designed for operation between 50 and 130° F. (10 and 55° C.)
  • Function with almost any oil or grease to 1,000,000 centipoise
  • Air operated check valves facilitate quick fill, quick dispense, and prevent leaking.
  • Threaded adjustment rod is visual indication of adjustment
  • Operate with grease inlet pressure between 400 and 3,000 psi

GMPD3000 series dispensers are also available with NPN stroke sensors, multiple stroke sensors, linear position sensors, and without stroke sensors.

Grease dispensers should always be installed as close to the dispense points as possible.

GPMD3007
GPMD3007
Air operated positive displacement grease dispenser adjustable between 40 and 62 cc. Includes one adjustable solid state sensor to indicate that the piston has stroked. Dispenser has 1/4 NPT outlet port, 1/8 NPT bleed port , and air pilot operated cartridge valves for inlet and outlet. Grease inlet pressure must be between 400- 3000 p.s.i. Boost ratio is 10.5 to 1. Requires 1850 Cord for proximity sensor. Dispenser requires either a 4 way air valve for operation or two 3 way NC air valves.
GPMD3007 Brochure Adobe Logo


No Image Available
GPMD3008
Air operated positive displacement grease dispenser adjustable between 2 and 25 cc.   Dispenser has 1/4 NPT outlet port, 1/8 NPT bleed port , and air pilot operated cartridge valves for inlet and outlet.  Grease inlet pressure must be between 400- 3000 p.s.i.  Boost ratio is 9.5 to 1.   Dispenser requires two or three 3 way NC air valves or time delay for fill for operation.


GPMD3009
GPMD3009
Air operated positive displacement grease dispenser adjustable between 15 and 210 cc.  Includestwo adjustable solid state sensors to indicate that the dispenser is "ready to dispense" and "dispense complete".  Dispenser has 3/8 NPT outlet port, 1/8 NPT bleed port , and air pilot operated cartridge valves for inlet and outlet.  Grease inlet pressure must be between 400- 3000 p.s.i.  Boost ratio is 19 to 1.   Requires two 1850 cords for sensors.  Dispenser requires two or three 3 way NC air valves.
GPMD3009 Brochure Adobe Logo


GPMD3013
GPMD3013

Air operated positive displacement grease dispenser adjustable between .04 and 4.00 cc.  Complete with 1/4 NPT inlet and outlet ports, 1/8 NPT bleed port, and air pilot operated cartridge valves for inlet and outlet.  Dispenser operation requires two or three 3-way NC air valves and grease pressure between 400-3,000 p.s.i.  Air valves can operate at 60 to 100 p.s.i.  Boost ratio is 20 to 1.  

Also available as GPMD3013PNP:

Air operated positive displacement grease dispenser adjustable between .04 and 4.00 cc.  Complete with 1/4 NPT inlet and outlet ports, 1/8 NPT bleed port, and air pilot operated cartridge valves for inlet and outlet.  Includes two 10-30 VDC PNP piston position sensors to be used as "dispensed" and "ready" inputs.  Dispenser operation requires two or three 3- way NC air valves and grease pressure between 400-3,000 p.s.i.  Air valves can operate at 60 to 100 p.s.i.  Boost ratio is 20 to 1.   Requires two 0983 Cords.


GPMD3013 Brochure Adobe Logo


GPMD3020
GPMD3020
Air operated positive displacement grease dispenser adjustable between 0.04 and 0.50 cc.  Complete with 1/4 NPT inlet port, 1/4" NPT outlet port, and air pilot operated cartridge valves for inlet and outlet.  Includes two 10-30 VDC PNP piston position sensors with M8 connectors to be used as "dispensed" and "ready" inputs.  Dispenser operation requires two or three 3- way NC air valves and grease pressure between 1,000 & 3,000 p.s.i.  Air valves can operate at 60 to 100 p.s.i.  Boost ratio is 39 to 1.   Requires two 0983 cords.
GPMD3020 Brochure Adobe Logo


 

OPTIONS

Part Number

Description

1850

Cord with 4-pin Micro connector

3850

Bleed valve with 1/8 NPT ports

EPS1001

Electronic Pressure Sensor – 0-60 bar (870 p.s.i.), SAE 04 male pressure fitting, 0 to 10 Volt output, 4-pin Micro connector.  Includes a sample program for use with A-B Micrologix PLC.  This sensor requires an analog input to the user’s PLC.

 

GPMD3000 Series Brochure Adobe Logo