GPMD15000 SERIES GREASE DISPENSERS

Nose-mountable, air-operated, single-acting, adjustable, metered shot (piston) dispenser 

Accurate dispensing of 0.02 cc to 6.20 cc shots of grease (depending on model selected).

 

Positive piston displacement dispenser accurately delivers measured shots of grease. 

Change shot size quickly and easily using fine-thread adjustment screw with a lock nut.

 

Swivel grease outlet allow inlet port to point in any direction and also facilitates easy installation

Can dispense up to 40 times per minute at the maximum shot size.

 

Uses piston displacement to measure grease and will dispense set amounts regardless of temperature.

Operate at 50 to 120 psi with 3-way NC Air Valve.

 

Operates with low-pressure grease (up to 200 psi).

 

Photos

Video

DISPENSER SPECIFICATIONS

Basic Part Number

Adjustable Volume

Boost Ratio (less return spring)

Note:

GPMD15020-__-__-__

0.02 to 0.20 cc

36 to 1

 

__-__-__  See OPTION LIST to complete part number. Include at least one option.  There is no maximum number of options. 

GPMD15080-__-__-__

0.02 to 0.80 cc

12.25 to 1

GPMD15125-__-__-__

0.06 to 1.25 cc

11.56 to 1

GPMD15369-__-__-__

0.13 to 3.69 cc

11.76 to 1

GPMD15620-__-__-__

2.00 to 6.20 cc

10.24 to 1

 
Notes: Basic part number must include at least one Option ID to be complete.  The part number for a dispenser with no options should include the suffix -00.  The GPMD15620-00 can not be adjusted to dispense less than 2 cc.
See complete part number examples below:  (enter suffix numbers in ascending order – lowest number to highest number)
GPMD15020-00 is a 15000 series dispenser with an adjustable volume of 0.02 to 0.20 cc, a boost ratio of 36 to 1, and no other installed options.  
GPMD15125-01-03-07 is a 15000 series dispenser with an adjustable volume of 0.06 to 1.25 cc, a boost ratio of 11.56 to 1, one stroke sensor, a calibration scale, and a manual bleed valve. 
 

Option ID

Description

Connector(s)

Factory Install?

Customer Install?

00

No Options (dispenser will have a magnetic piston)

Not Applicable

-

-

01

Single M8 PNP Stroke Sensor

One M8 DC

Yes (with track)

No

02

Two M8 PNP Stroke Sensors

Two M8 DC

Yes (with track)

No

03

Calibration Scale

Not Applicable

Yes

Yes

06

Digital Flow Sensor with 2 PNP outputs. 1000 psi

One M12 DC

Yes

No

07

Manual Bleed Valve installed in place of 1/8” NPT bleed plug

Not Applicable

Yes

Yes

09

Flow sensor has 2 PNP outputs and an M12 connector. For 3,000 psi max.

One M12 DC

Yes

Yes

11

KA6003 mounting block installed on dispenser with 1/4” NPT female outlet, vertical and horizontal mounting holes and an SAE-4 port for (not included) EPS1001 electronic pressure sensor.

Not Applicable

Yes

Yes

12

Two M8 NPN Stroke Sensors

Two M8 DC

Yes (with track)

No

15

Single M8 NPN Stroke Sensor

One M8 DC

Yes (with track)

No

20

Analog Flow sensor (0-10 Volt)

One M12 DC

Yes

No

21

Clamp bracket used to side mount dispenser.

Not Applicable

Yes

Yes

22

Premium Seals for Use with Abrasive Material

Not Applicable

Yes

Yes

23

Air Operated Outlet Check Valve

Not Applicable

Yes

No

26

Stainless Steel Inlet Check Block

Not Applicable

Yes

Yes

 

Files